IMPLANTS
Onbutton
Solid fixation for either primary or auxiliary fixation in ACL or PCL reconstruction. Distal fixation allows circumferential healing of the ACL graft to tunnel wall. Significantly enhances soft tissue apposition to bone to speed healing and strengthen the repair. Material -Titanium alloy.
Low-profile cancellous screws & Spiked washers
Low profile cancellous screws provide continuous strength for soft tissue fixation to bone. Low profile head to reduce soft tissue irritation. Can be used as a post screw for suture or soft tissue fixation. Ideal for ACL, PCL, collateral ligament or posteriolateral reconstruction. Unique washer design with spikes on the inferior surface provides excellent fixation of soft tissue to bone. Available in diameter 6.5mm and lengths 35mm and 40mm. Material - Titanium alloy.
Tibial post fixation screws
Used to securely trap attached sutures and bulky suture knots atraumatically under the low profile head to eliminate soft tissue irritation. Available in diameter 6.5mm and lengths 30mm. Material - Titanium alloy.
Spiked ligament staples
Used for the ligament to bone fixation. Designed to have sharp leg points for easier penetration into cortical bone. Two pronged implant for superior pull out strength. Available in two sizes-small and large. Material -Titanium alloy.
Cannulated cross pins
Cannulated cross pin provides the surgeon with maximum pull-out strength while maintaining fast and efficient implantation methods. Increased graft compression in the femoral tunnel gives a secure transverse femoral fixation second to none. With single cross pin fixation, the length and load to all four graft strands are equalized independent of tibial fixation, maximizing graft stiffness. Allows insertion by impaction and has reverse cutting threads for screw-out removal. Available in length 50mm. Material - Titanium alloy.
Tibial base plates
Used for tibial fixation of the ACL and PCL graft. Indirect extra-articular fixation of tibial and tibial-end of the graft. Available in two versions-round hole and D-hole. Material -Titanium alloy.
Cannulated interference roundhead screws
Specifically designed for endoscopic femoral fixation where graft protection is needed. Polished, fully radiused threads provide maximum graft protection. Wide-bore cannulation for easy guide wire removal. The Taper-Tip style offers sharper initiating threads and a more pronounced taper for faster, easier insertion. Round head reduces possibility of graft damage during or after implantation. Standard 4.5mm hex for easier insertion and removal. Available in diameters 8mm, 9mm, 10mm and 11mm. Available in lengths 20mm, 25mm, 30mm and 35mm. Material -Titanium alloy.
Cannulated interference fully threaded screws
Universal screw for either tibial or femoral applications. Standard 4.5mm hex for easy insertion. Cannulated for use with a guide wire. Designed to reduce the possibility of bone plug migration during placement. Available in diameters 8mm, 9mm, 10mm and 11mm. Available in lengths 20mm, 25mm, 30mm and 35mm. Material -Titanium alloy.
BIDDU Tibial A/P Sloped Osteotomy Plates
Opening wedge. Precise, sloped plate. For tibial Osteotomy. Maintains normal anatomy. Available in sizes 7.5mm, 10mm, 12.5mm and 15mm. Material - Steel.
INSTRUMENTS
ONLoc Drill guide system
A highly precise drill guide available for cruciate reconstruction-The ONLoc Drill Guide conforms to each patient’s anatomy, offering surgeons flexibility, accuracy and control. The ONLoc Drill Guide is compact, for easier handling and added control. It was designed not only to fit comfortably in the surgeon’s hand, but to accommodate the full spectrum of knee anatomy.
The key features of the ONLoc Drill Guide are: A dovetail arm design. An ergonomic guide handle precisely fitted for the surgeon’s hand. Simple locking mechanism for one-handed operation of the guide. Light-weight and compact for added control. An angled bullet for engaging the cortex more consistently and securely. A rectangular guide arm cross section that is more rigid than round cross section designs. Comprises of Angled Bullet, ACL Elbow Aimer, PCL Tibial Aimer, PCL Femoral Aimer.
Drill bit passing pins
Cat. No.-BAK-7036.
Graft passing guide pins
Cat. No.-BAK-7037.
Cannulated Tibial Reamers
Used for drilling bone tunnels in ACL and PCL reconstruction procedures. Cannulated for use with a 2.4mm drill tip guide pin. Graduated depth marks on three sides for easy identification of bone tunnel depth. Available in diameters ranging from 6mm to 12mm.
Cannulated Femoral Flowertip Reamers
Suited for an endoscopic ACL technique whereby the femoral tunnel is reamed from inside-out while minimizing the risk of injury to the PCL. Drill bit shaft is etched with depth marks on three sides for easy identification of bone tunnel depth. Facilitates open femoral tunnel preparation and in-line tunnel reaming for endosteal fixation procedures. Head profile permits easy withdrawal from bone tunnels. Available in diameters ranging from 6mm to 12mm.
Cannulated Endoscopic Reamers, dia.4.5mm
For use with Onbutton and Interference screws. Cat. No.-BAK-7052.
Depth Gauges for ACL/PCL reconstruction
Cat. No.-BAK-7053.
Femoral Aimers
Used in ACL reconstruction to create the portal socket in order to place the graft passing pin through the anteromedial portal. Available in sizes 5mm, 6mm and 7mm.
Bone Tunnel Plugs
Helps to control fluid loss while providing a sealed instrumental portal. Available in sizes 7-8mm, 8-9mm and 9-10mm. Also available in cannulated versions.
Tunnel Dilators
Expand tibial and femoral tunnels while compressing the cancellous bone without drilling. Tapered ends allow for easy insertion and removal of the dilators from the femoral or tibial tunnel. Full radiused depth marks in 5mm increments. T-Handle-ergonomic styling allows for an easy grip and manoeuvrability; built in locking quick connector; allows for easy intraoperative changing, as well as minimizing the potential for the units to separate during use. Available in diameters ranging from 6mm to 10mm. Also available in cannulated versions.
Cannulated screwdriver for interference screws
Cat. No.-BAK-7063.
Impactor for spiked ligament staple
Cat. No.-BAK-7064.
Arthroscopic Knee Probes
Ergonomically designed calibrated probe allows the surgeon to accurately quantify pathology.Microfracture Awls Allow the creation of localized vascular access channels in chondral defects. Also useful to mark intended drill sites in all ACL/PCL procedures. Available in 300,